Just about everyone has their own theory involving How to Install a Bathtub Yourself.
Setting up a bathtub isn't precisely brain surgery, however it does require solid plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably challenging project. If the old bathtub is readily available, the project can relocate speedily; if you have to open a wall surface to remove the old bathtub and place the brand-new tub, the task is much harder. In either situation, the project is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old tub and embeded in the new one. Make certain you have actually certified on your own for the job and fit trying it. As opposed to hiring a service provider to take over a halfway-completed task, it is better to consider utilizing one before you begin. Opportunities are you might require a professional plumber to make tube links.
This article will certainly aid you install a brand-new bath tub in your washroom if you have actually currently purchased a new tub as well as don't require to transform the plan of your previous water system pipes.
Your tools and also product list need to make up the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is separate the water system. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the restricted access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to going on to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Secure the tap in position with the supplier provided backnut. Once the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type must be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Making use of both wooden boards under its feet, place the bath tub in the required position. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the tub till the spirit level reads level.
To mount faucets, fit the bottom of the furthest adaptable tap connector to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the water supply and also check all joints and also new pipework for leakages and tighten them if essential. Fill the bath tub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Finally, repair the bathroom paneling as defined in the producer's user's manual. Tiling and also securing around the bathtub ought to wait up until the bath tub has been used at the very least when as this will resolve it into its last position.
Getting ready for the Installation
Firstly, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets device to prevent strain on the tub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to currently prepare to be fitted in its final setting.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to break a stiff seal, creating the water to penetrate the wall surface in between the bath and the tiling, bring about complications with moisture and also feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and fittings. They are sold in tubes as well as cartridges, and are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water before securing, to enable the motion experienced when the tub remains in use. The sealer can break fairly very early if you do not think about this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the floor tiles making use of water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious reader on Installing A Bathtub, I think sharing that excerpt was smart. Feel free to take a moment to distribute this post if you enjoyed reading it. Thank-you for going through it.
Plumbing insights available.